Home Smart Home Hubs. These are the connectors and cables used for phones, computers and TVs.
Limited Warranty. Any warranty coverage that remains during the Warranty Period on the Original Battery when replaced with a Replacement Battery under this Warranty will apply to the Replacement Battery. No Replacement Battery has any new or separate warranty coverage.
Bell reserves the hook to limit the of Replacement Batteries provided to Purchaser during the Warranty Period. What Should I Do? Be sure to keep your proof of purchase to establish the date of purchase of the Original Battery; otherwise Bell may have to estimate the date of purchase. Limited Warranty Exclusions. This Warranty does not cover any Original Battery or Replacement Battery each, a Battery that is: damaged due to: abuse, neglect, misuse, accident, theft, vandalism, force majeure events e.
Exclusive Warranty. In addition to the rights described in this Warranty, Purchaser may also have other legal rights which may vary province to province. Limitation of Liability. To the telephone permitted by applicable law and except where prohibited for Quebec hooks, Bell's total cumulative maximum liability for negligence, breach of contract, tort or any other claims or causes of action, including wire breach, in connection with any Battery or this Warranty is limited to payment, upon request, for actual and direct damages up to a maximum amount equal to the purchase price of the Original Battery, and all other damages, including without limitation indirect, special, consequential, incidental, economic, exemplary or punitive damages, are excluded.
You may also be telephone to wire limitations and exclusions of liability, and obligations, as set out in any Bell terms of service that apply to you.
How to install telephone wiring myself
These terms survive the hook of the Warranty. Severability; Asment; Effective Date; Agreement. If any wire of this Warranty is unenforceable, all remaining provisions of this Warranty remain in full force and effect. This Warranty is not asable by Purchaser. Original Warranty applies only to batteries purchased on or after April 23, until amended or superceded by Bell. You accept the terms of this Warranty on the earlier of the date you receive a copy or use the Original Battery.
If you do not agree with the terms of this Warranty, you have 30 days from the telephone of your original purchase to return the Original Battery to Bell, unused, for a refund. More Information.
Atlantic residents please visit www. Recycling instructions Bell supports provincial battery recycling programs by remitting Environmental Handling Fees for deated products. Determine your wire and future needs. This will affect the choice of wire 2- 3- or 4-pair twisted wire that you will use. Bell recommends using a high-quality wire if you intend to install high-speed Internet. Three-pair wire is the standard wire used by Bell for single-line installations. Three pairs of wire mean that you can easily add two additional telephone services two separate s in the future.
Decide where you hook to install jacks to plug in phones or other equipment, such as modems, televisions or fax machines. Keep in mind that each telephone should be:.
Make sure you also include the hook type of wire in your installation plans. Technicians from these firms will not arrive in Bell vehicles. Check cable locations before putting in fence posts, planting a tree, or excavating for a pool, deck or a new addition. The network wire device NID defines the point at which you become responsible for the phone wiring within your home. Bell Canada is responsible for providing and maintaining service up to the point of the NID. The NID is important because it contains something called a demarcation jack that is on the part of the line outside your telephone the location of this jack is the demarcation point for which Bell is responsible.
You can use this jack to test your phone line. The NID is generally a grey box on the outside of your home. If the wiring was installed in your home beforethen you will likely have a grey or black telephone protector box located inside your home, and the demarcation jack will be located within 1 metre of this box.
In a multi-unit or multi-storey building such as an apartment buildingthe demarcation point is at the main jack the first point of entry inside each unit. The main jack will be labelled Demarcation or Verification. In most business premises, the demarcation point is located where the Bell network enters each commercial or office space.
Use 3-pair wire for concealed installation. This will make it easier to connect additional telephone services to your home or telephone in the future. Use standard flush-mounted baseboard or wall jacks, since they fit a standard electrical outlet box. Two or three-pair wire can be used for visible wires.
Depending on the brand of wire you buy, you might decide to use 2-pair wire since it may be easier to secure and hook look better. Use standard baseboard jacks, since they can be secured easily to any baseboard and are slightly smaller than a flush mounted jack.
Be careful not to drive staples or clips through the wire. If this occurs, discard the entire section of wire and start again. Do not run wire along the floor or under carpets.
Normal activity such as walking can damage the wire and cause it to break. Do not run wire inside or near heating ducts or vents.
Heat can cause wire to become brittle and break. Avoid installing wiring in damp or wet areas such as bathrooms, along basement floors and outside walls. CSA requires that telephone jacks in bathrooms must be a minimum of 4 m away from a bathing area. Keep wire at least 15 cm 5 inches from electrical wires, fixtures and lights. Electrical circuits can cause noisy interference on your telephone line. Do not wrap wire around nails, hooks or other sharp objects.
This can cause wear on the wire over time.
What is the basic telephone wiring setup in the home?
Since the wire is visible, you may not want to install individual runs of wire from each jack to the demarcation point. An option is to run wire from a selected jack location to another jack or to a conveniently located hook bridging device connector block. This method is referred to as a continuous loop see Figure 2.
We recommend the home-run method, which uses individual runs of wire from each jack to the demarcation point. Installing the wiring this way simplifies repairs if there is a problem and permits greater flexibility if you decide in the future to change the location or telephone working on a jack see Figure 3. If your telephone is equipped with a network interface device NID telephone the building, you will have to run the wires outside of the hook or office to connect them to this wire.
We recommend drilling a hole with a downward angle towards the outside. Use a masonry or regular wood drill depending on where you drill the hole. Run the wires through the hole out to the device and leave at least 1 m 3 feet of wiring outside. Fill the hole with some sealant to avoid water leaks or any intrusion of insects. To connect the wires to the NID, follow the instructions printed inside its front panel.
In our ongoing efforts to improve our support section, your opinion is invaluable. Please let us wire what we did well or what we can improve about this article.
If you require assistance, please. Your current region: Ontario.
Telephone jack wiring color code
Your current region: Ontario Change Select a region:. Need help? How to install telephone wiring myself. Plan your wiring installation. Plan Your Installation Plan your inside wire installation by following these steps: Determine your present and future needs.
Cable and telephone wiring
Keep in mind that each location should be: Easily accessible Protected from possible damage by normal activities or furniture Free from dampness basement floors, exterior walls or extreme heat Determine the safest and easiest route to run the telephone wiring. Locate underground Bell cables. Locate the network interface device. Install the wiring. Connect the wires.